product description
EBC Prolite brake disc floating, full floater. MADE IN UK.
The aim of the development is to improve the braking behavior
opposite the original brake disc. EBC uses HPSR steel
with a low carbon content, one 18% higher
Has friction coefficient. This steel is much more resistant
against rust as cast steel. In addition, the entire surface is with
protected by a 3 micron thick layer of zinc, which is in the range of
Brake pad contact zone already abraded during braking. Only
In this area, flash rust can be formed more easily with a longer service life.
Fits all BMW R65 / R80 / R100 Monolever models (1 rear shock absorber)
The brake discs are drilled in the bird's swing design to work with
few holes as possible with simultaneous optimized cleaning of the
Brake disc of rainwater and brake dust to get along.
The fewer holes you have, the better
Wet braking behavior and the lower the wear.
Technical specifications
- Outside diameter: about 285 mm
- Inner diameter: approx. 62.2 mm
- Bolt circle: approx. 80 mm
- number of holes: 4
- Bore diameter: approx. 10.5 mm
- Thickness: approx. 4.7 mm
- Offset: approx. 23.3 mm
- Page: left
- Version: floating
- Manufacturer: EBC
- Approval: ABE
advantages
- Brake ring machined from forged HPSR low carbon steel.
- Therefore no distortion of the brake disc even at maximum load.
- No vitrification of the braking surface, friction coefficient therefore remains constant.
- drilled brake surface with optimized hole pattern.
- Galvanized for protection against corrosion.
- Anodized aluminum hub.
- Lowest manufacturing tolerances.
- EBC recommends EBC Double-H Sinter brake pads for best braking performance.
- Independent design.
This offer is only the left brake disc!
The right brake disc can be found in our shop
under the article number: BR-BER
Matching brake pads can be found under the article numbers:
BR-BSI (sintered) and BR-BST (standard)
The aim of the development is to improve the braking behavior
opposite the original brake disc. EBC uses HPSR steel
with a low carbon content, one 18% higher
Has friction coefficient. This steel is much more resistant
against rust as cast steel. In addition, the entire surface is with
protected by a 3 micron thick layer of zinc, which is in the range of
Brake pad contact zone already abraded during braking. Only
In this area, flash rust can be formed more easily with a longer service life.
Fits all BMW R65 / R80 / R100 Monolever models (1 rear shock absorber)
The brake discs are drilled in the bird's swing design to work with
few holes as possible with simultaneous optimized cleaning of the
Brake disc of rainwater and brake dust to get along.
The fewer holes you have, the better
Wet braking behavior and the lower the wear.
Technical specifications
- Outside diameter: about 285 mm
- Inner diameter: approx. 62.2 mm
- Bolt circle: approx. 80 mm
- number of holes: 4
- Bore diameter: approx. 10.5 mm
- Thickness: approx. 4.7 mm
- Offset: approx. 23.3 mm
- Page: left
- Version: floating
- Manufacturer: EBC
- Approval: ABE
advantages
- Brake ring machined from forged HPSR low carbon steel.
- Therefore no distortion of the brake disc even at maximum load.
- No vitrification of the braking surface, friction coefficient therefore remains constant.
- drilled brake surface with optimized hole pattern.
- Galvanized for protection against corrosion.
- Anodized aluminum hub.
- Lowest manufacturing tolerances.
- EBC recommends EBC Double-H Sinter brake pads for best braking performance.
- Independent design.
This offer is only the left brake disc!
The right brake disc can be found in our shop
under the article number: BR-BER
Matching brake pads can be found under the article numbers:
BR-BSI (sintered) and BR-BST (standard)
Customers also purchased
